产品（矿用风动/气动切割锯）介绍： 
1.该锯适用于危险的工作环境，可在较高温的环境下作业，无火花，在潮湿的环境中无漏电危险，是一款性能可靠、安全型及效率极高的理想风动工具之一。广泛用于采矿、石化、建筑等行业。 
2.利用井下压风管道系统作为动力源。重量轻，易携带；结构科学，便于作业。 
3.可快速切割管道、电缆、角钢、结构钢、U型钢、链条、锚杆、锚索等。 
4.锢金属钢合金超级锯条，耐高温、耐摩擦、使用寿命长。非常适用于锯割不锈钢、镍基合金、铁、铜、铝、玻璃、塑料、木材等。
 
技术参数：
型号  FDJ-230 
功率  2kw 
耗气量  0.8
切割宽度（直径）  230mm 
锯片速度  60m/min

重量  8kg 

使用方法：
  1、了解所需切割的材料。
  2、确保牢固固定了所需切割的材料，防止其移动。
  3、电源接上时，用手指按压阀杆，然后开始切割。
  4、用锯的重量来控制切割压力。对于较软的材料来说，这样的重量已经足够。过多的压力会降低锯片的速度。对于较硬的材料，可以通过加压的方式来降低锯片的转动速度。切割是保持锯笔直。锯片的任何扭曲或歪斜都可能降低其使用寿命。（注意：避开切割后可能掉落的碎片。切割即将完成时，切勿使锯碰到您的身体、工件或附近的其它人员。）
  5、下次切割开始前，锯片必须保持运动状态。气动锯时，锯片不能接触任何表面。
  6、更换锯片前，务必断开气动力。
  7、顺时针转动调整手柄以便释放锯片导杆上的张力。然后释放侧面板的锁以便打开侧面板。然后从驱动轮上取下锯片并将其从锯带导杆上松开。
为了安全作业需要注意以下几点：
   1、用锯的重量来控制切割压力。对于较软的材料来说，这样的重量已经足够。过多的压力会降低锯片的速度。对于较硬的材料，可以通过加压的方式来降低锯片的转动速度。切割是保持锯笔直。锯片的任何扭曲或歪斜都可能降低其使用寿命
  2、关闭气源时，释放阀杆。
  3、更换锯片前，务必断气动源。
  4、顺时针转动调整手柄以便释放锯片导杆上的张力。然后释放侧面板的锁以便打开侧面板。然后从驱动轮上取下锯片并将其从锯带导杆上松开。
  5、下次切割开始前，锯片必须保持运动状态。气动锯时，锯片不能接触任何表面。
  6、了解所需切割的材料。
  7、确保牢固固定了所需切割的材料，防止其移动。
  8、接好气时，用手指按压阀杆，然后开始切割。
特点：
1.轻便型现场移动活跃作业，瓦斯管，自来水管，电器，机械车间，建设，煤矿及其他切断作业现场。
2.台湾携带式小型锯床，无需冷却液，自然干切。
3.切割材料范围广，在规定硬度范围内的金属、非金属都能切割。
4.精加工，切割面平整，大大提高工作过效率。 5.切割角度可调整，0到90度。

联系人金志鹏电话13934240041
Usage method：
1, what's needed to cut materials.
2, to ensure that the firmly required cutting material, to prevent the mobile.
3, connected with the power on, press with your fingers and began cutting stem.
4, saw the weight to control the cutting pressure. For soft materials, the weight is enough. Too much pressure will reduce the speed of the saw blade. For hard materials, to reduce the rotational speed of the saw blade by pressurized method. Keep straight cutting saw. Any distortion or skewed blade may reduce its service life. (Note: avoid cutting debris may fall. Cutting is finished, do not make contact with other staff saw your body, the workpiece or nearby).
5, before the start of the next cut, the blade must keep moving. Pneumatic saw, saw blade can not touch any surface.
6, replacing the saw blade, be sure to disconnect the gas power.
7, clockwise adjust the handle to release the tension on the saw blade guide rod. Then release the lock side panel to open the side panel. And then removed from the drive wheel and the blade from the saw belt guide rod release.



In order to safety work should pay attention to the following points:
1, saw the weight to control the cutting pressure. For soft materials, the weight is enough. Too much pressure will reduce the speed of the saw blade. For hard materials, to reduce the rotational speed of the saw blade by pressurized method. Keep straight cutting saw. Any distortion or skewed blade may reduce its service life
2, closed source, release valve.
3, replacing the saw blade, must die moving source.
4, clockwise adjust the handle to release the tension on the saw blade guide rod. Then release the lock side panel to open the side panel. And then removed from the drive wheel and the blade from the saw belt guide rod release.
5, before the start of the next cut, the blade must keep moving. Pneumatic saw, saw blade can not touch any surface.
6, what's needed to cut materials.
7, to ensure that the firmly required cutting material, to prevent the mobile.
8, aerobic, pressing with a finger and began cutting stem.
Characteristic：
1. portable mobile active site operation, gas pipe, tap water pipe, electric appliance, mechanical workshop, construction, coal and other cutting operation site.
2. Taiwan small portable machine, without cooling liquid, natural dry cutting.
3. cutting a wide range of materials, within the specified range of hardness of metals and non metals can be cut.
4. finish, smooth cutting surface, greatly improve work efficiency. 5. the cutting angle can be adjusted to 0 to 90 degrees.